top of page

FIPRO SG 560

PRODUCTS FOR THE REMOVAL OF ORGANIC AND INORGANIC CONTAMINANTS FROM MULTIMETAL SURFACES

Technical features

FIPRO SG 560 is a completely volatile solvent that has a barely perceptible odor that does not develop over time, even when exposed to heat and light, unlike other conventional hydrocarbon solvents. This feature makes it ideal for uses where a pleasant smell is essential such as household products, for cleaning electronic components and metal surfaces, liquid for barbecues, products for cosmetics, for graphics and for the production of odorless paints, but also in the textile, engineering, motor industry in general, in the transport sector. It has a low solvent power towards most resins, plastics and rubbers, allowing safe use even in the presence of various kinds of gaskets. However, given the large variety of synthetic materials available on the market, it is advisable to carry out a preliminary compatibility test, by immersing a sample of the material in the FIPRO SG 560, lasting a few hours. In the mechanical sector it is used for degreasing metal surfaces, interoperable or before painting or other treatments. It has been designed for all cleaning operations, by rag or immersion, where the use of pure chlorinated solvents is not recommended.
FIPRO SG 560 removes contamination consisting of oils, dusts, greases, etc.

Usage and Applications

If used by immersion:
Simply immerse the pieces to be cleaned in the product, preferably with slight agitation, especially in the presence of solid particles and / or adhering chips.
The operating temperature can vary from room to 30-32 ° C. However, it is advisable not to exceed the flash point.
The drying speed of the pieces depends on the operating temperature: working in cold environments, it is convenient to let the pieces drip accurately after extraction, and leave them exposed in a ventilated environment for at least fifteen minutes, to allow complete drying.
The product can - very conveniently - be used in the presence of ultrasounds as degreasing accelerators. This is especially useful if the surfaces are soiled with solid adhering residues.
If used by brush:
The product is particularly suitable for application by cloth or brush. In this case, the mechanical rubbing action, combined with the emollient and solvent power of the product and its penetration capacity (even where tolerances are extremely small) allows perfect and quick cleaning of the pieces subjected to treatment.

Physical-Chemical Data

Parametro
Valore
Appearance
Colorless liquid
Smell
Characteristic
Flammability VA °C
>21
Specific Weight at 20 °C
0,765 Kg/l
Solubility in Water
Not miscible

Storage

We recommend metal tubs: for example iron or steel are perfectly suitable. The fittings can be in brass. For implant materials in contact with the product, we do not recommend the use of rubbers and paints which, in the long run, could be damaged or swollen.
Any heating elements can be in stainless steel (or, with a lesser guarantee of duration over time, in copper). As far as heating is concerned, absolutely avoid the use of immersed electric resistances, due to the danger of overheating and malfunctions which could cause a fire. Use heating fluids (eg hot water) and set up an additional safety thermostat at a temperature below 35 ° C.

Applicazione
Concentrazione

Highlights

  • Multi-material degreasers

  • Pre and Post processing treatments

  • Low environmental impact alternatives

  • Longevity and effectiveness

  • Periodic checks

  • Formulated, produced and controlled internally

Application

  • Removal of whole and emulsifiable oils, fats and processing pastes

  • Dephosphating

  • Removal of polishing pastes from parts and small parts

  • Removal of interoperational, protective, polymer films and silicones

  • Etching, pre-painting, pre-conversion treatments

  • Cleaning of plastics and glass

  • Interoperational or final cleaning of the product

Interessato?

Scrivici subito!

Privacy

Dichiaro di avere compiuto sedici anni, e se minore di sedici, di essere stato autorizzato dal titolare della responsabilità genitoriale, pertanto acconsento al trattamento dei miei dati personali così come indicato nella Privacy Policy.

Comunicazioni

Acconsento al trattamento dei miei dati personali. Per l’inoltro della newsletter, le comunicazioni via telefono (sms, WhatsApp, telefonata vocale)

Prodotti Correlati

FIPRO SG 562

Low foam liquid degreaser suitable for washing all metals in both spray washing machines and immersion tanks.

Ideal for removing, even at low temperatures, the most stubborn contaminants such as oils, greases, molding and drawing pastes, and carbonized oils.

FIPRO SG 564

Volatile solvent that has a barely perceptible odor.
Designed for all cleaning operations, by rag or immersion, where the use of pure chlorinated solvents is not recommended.

FIPRO SG 565

Liquid, alkaline, amine-based interoperational degreaser. During storage, it guarantees 1-1.5 months of protection of the pieces. Can be used in single-stage and multi-stage washing machines, effective in the removal of numerous types of emulsifiable and whole oils.

UN PO' DI NOI

Fusti di stoccaggio

LA NOSTRA PRODUZIONE

Tutte le linee Fiprokim sono prodotte presso la nostra sede di Altavilla Vicentina.

La vasta gamma di miscelatori ed apparecchiature ci permette di avere una notevole potenza produttiva.

FREZZE 4-mod.jpg

PRODOTTI SU MISURA

Fiprokim si avvale di un laboratorio di ricerca e sviluppo formato da tecnici specializzati nei vari settori.

Lo studio delle soluzioni tecniche, la selezione ed il controllo delle materie prime fanno parte del processo di creazione di un prodotto efficace.

immagine azienda ridimensionata.jpg

LA NOSTRA AZIENDA

Fiprokim ha una più che ventennale esperienza nel campo della ricerca, formulazione, produzione e commercializzazione di prodotti chimici per il trattamento dei metalli  e la loro detergenza e di lubrorefrigeranti per la lavorazione meccanica dei metalli.

bottom of page