FIPROPHOS 514

PRODUCTS FOR SURFACE CONVERSION AND PRE-PAINTING

Technical features

FIPROPHOS 514 is a single-component liquid phospho-degreaser, specially designed for the treatment of ferrous material, galvanized steel and aluminum. FIPROPHOS 514 creates on the treated surfaces an amorphous phosphate layer of high compactness and thickness 10 mgr / dmq which constitutes an excellent anchoring base for liquid, powder or electrophoretic paints. The correct use of the product requires a subsequent continuous partial renewal rinse and possibly a final rinse with demineralized water. A suitable final passivation further improves the anticorrosive resistance results.

Physical-Chemical Data

Parametro
Valore

Usage and Applications

FIPROPHOS 514 is used as a pre-painting treatment, with higher performance than medium weight phospho-degreasers, for accessory parts in the automotive industry, household appliances, metal furniture and sheet metal products in general.

Applicazione
Concentrazione

Bathe preparation

  • Fill the tank with clean tap water up to approximately three quarters of its volume

  • Start the recirculation pumps and bring to the working temperature

  • Add 15-60 kg (13-50 liters) of FIPROPHOS 514 for every 1000 I of bath

  • Bring the bath to the exact volume and working temperature, leaving it in recirculation for 15-20 '

  • Check the working parameters; it may be necessary to bring the pH value within the operating range by adding small amounts of ALCAFIP 250

Control of bathing

  • Deposition of a homogeneous protective substrate

  • Easy to start and run process

  • Low environmental impact and non-hazardous products

  • Increased hours of salt spray

  • Increased adhesion of paints and coatings

  • Preconversion or final treatment

Alimentation

The bath is fed with FIPROPHOS 514 according to the score (total acidity).
To obtain the concentration in gr / lt multiply the value obtained by the fixed number 5.1.
Then bring the concentration to the required value, adding 5.1 kg of product per 1000 Lt. of bath for each missing point.
As the bath ages, a physiological increase in pH and / or score may occur. In this case the bath supply will be managed according to the maintenance of the pH value within the operating range, until the renewal of the tank.

Warnings

If you notice an accumulation of oil on the surface of the bath, it is advisable to partially brush it in order to avoid contamination of the treated material.
For the tanks and other parts of the system it is advisable to use stainless steel (preferably AISI 316 or 316 L).
The pumps to be installed in the individual areas must have characteristics such as to ensure a spray pressure of at least 1.5 atm in all active phases, with the exception of the final passivation, which admits a lower pressure (0.8 - 1 atm). Higher pressures can favor degreasing.
Prolonged exposure of FIPROPHOS 514 to light and heat can cause color variations.
Slight differences in the appearance of the product do not compromise its efficiency and operational performance.

Interessato?

Privacy

Dichiaro di avere compiuto sedici anni, e se minore di sedici, di essere stato autorizzato dal titolare della responsabilità genitoriale, pertanto acconsento al trattamento dei miei dati personali così come indicato nella Privacy Policy.

Comunicazioni

Acconsento al trattamento dei miei dati personali. Per l’inoltro della newsletter, le comunicazioni via telefono (sms, WhatsApp, telefonata vocale)

Scrivici subito!

Prodotti Correlati

UN PO' DI NOI

Fusti di stoccaggio

LA NOSTRA PRODUZIONE

Tutte le linee Fiprokim sono prodotte presso la nostra sede di Altavilla Vicentina.

La vasta gamma di miscelatori ed apparecchiature ci permette di avere una notevole potenza produttiva.

FREZZE 4-mod.jpg

PRODOTTI SU MISURA

Fiprokim si avvale di un laboratorio di ricerca e sviluppo formato da tecnici specializzati nei vari settori.

Lo studio delle soluzioni tecniche, la selezione ed il controllo delle materie prime fanno parte del processo di creazione di un prodotto efficace.

immagine azienda ridimensionata.jpg

LA NOSTRA AZIENDA

Fiprokim ha una più che ventennale esperienza nel campo della ricerca, formulazione, produzione e commercializzazione di prodotti chimici per il trattamento dei metalli  e la loro detergenza e di lubrorefrigeranti per la lavorazione meccanica dei metalli.